Search results

I have a Iron Horse 3500psi Hot Water Pressure Washer. I never noticed it before, But I have very heavy black smoke coming out of my stack. I notice it goes away when I am letting it idle for a few minutes, but as soon as I pull the trigger I get lots of black smoke once again. Do I need to...

How do I post my photo? I tried uploding it from my computer and it never shows up?? Watch it show up now? jaime

I have been in business for a little less than ten years full time through good and bad. However I lately have been having the itch to Sell Sell Sell!!!!! I really don't want to in my heart, but due to all the scheduling problems, non regular paying customers, employees calling off, etc. I...

I have a vinyl siding and brick home to wash next week. Two sides of each. Plus a small deck out back about 10 X 12 oh plus 1 flight of wood steps. House is a typical new two story old farm looking house with brick porch on front. Lots of windows front and back none on the sides. This is a guy...

I have some contracts that I do on a weekly and semi-weekly basis. The problem is that they wait 30 to 90 days to pay me. MY terms are net 10 days. I can charge interest only after 30 days though. I was thinking about charging a flat fee like $10.00 to $20.00 any time after the 10 days. However...

Has anyone ever tried mixing these two to make a degreaser? Dawn Works on my hands when I get home from work. Just wondering? I figure if you mix the two you would be paying less than a $100.00 a 55 gallon(RTU)drum. Just tryimg to save muney on chemicals! Any imput would be helpful. Thanks...

I am a proud new Dad (AKA Da da da da) Just showing of my daughter! Any other power washers have children, spouses, dogs, cats, fish, snakes, rocks, etc. How about hobbies when your not working? (Not working what's that!) Just wondering? Jaime ------------------

I was just thinking there has to a cheaper way to keep replacing the bars on my Steel Eagle. I have employees who "kill" them on a regular basis. I am sick of spending a hundred bucks every time they get a little bent. I would like to make my own but not sure where to buy the stuff. (Stainless...

Does anyone know what the sic code is for power/pressure washing? I have been looking for hours and can't come up with one. My insurance application asked for one. They said I did not need it but now I am just curious!!!! Thanks Jaime

Has anyone ever taken apart a spindle from Steel Eagle? The spindle is not leaking but it sounds like the bearings are going. I have grased it like required and DID NOT over grease it! Thought I might be cheap this time and just replace bearings. Any thoughts would be appreciated. Thanks Jaime

I had a guy come over to my job site and he stated that my pressure washer was to loud. It was about 9:00pm and I was soon going to be done by 10:00pm. He told me he was going to call the police if I did not stop at that moment. I said I would do him a favor and call myself. I found out I was...

I unpacked it today and used tonight and it worked very nice except for it leaking on top of the deck. I mean.... I checked everything from top to bottom but I had a very heavy stream of water running on top of the deck? Anyone had this trouble? I'm calling them tommorrow to ask! Thanks, Jaime

I am thinking of purchasing a new Hot water unit. Any Suggestions? Would like a 4gpm at 4000 unit. Under or around $4000.00 Iron Horse or Tuff Part #T4040G for $3,345.00 General Admiral or Giant pump? Other brands? Thanks Jaime

Is there anyway we can trade pictures of our families and trucks on here? I know there is email but we would have to collect all the email addresses from everyone. I always like to know who I am talking to. Jaime

Looking for new degreaser and have a lot of emails on both. Any input? Jaime

Dan, Maybe have a section for "seniors" in the business say 8, 9 , 10+ years in business. Instead of how many times you post. Because I realized that I can't be on here EVERY SINGLE day. Have to work, Yeh no!!! So I can buy more toys. Oh I mean tools. lol Jaime

I currantly use this product now but I buy it thru a supplier. I know The Stockdale Company manufactures it. I would like to buy it wholesale do to the volume I go thru in a month. I think they (The Stockdale Company) are from New Jersey but I'm not sure. The product is called Hyrdo Blast or...

What would be the going rate for stripping and waxing of floors. Last time I checked it was .15 to .18 cents a square foot. To Low to High? Jaime

I love this Board because you must register. Very good idea. Keeps out the riff raff. All of us know how hard it is to survive in this business because of weekenders, down time, weather, competition, etc. I like to know who I am talking to and were they are from. I am more than GLAD to help...